Drawing to BOQpipeline control sheet
← Mindmapwhat the drawings said

Longitudinal Girder

1 page · 1 crop · superstructure

Matched toMain Girderbridge.superstructure.main_load_system.girderon “Longitudinal Girder”

1 read off the drawings · 4 not established
The class asks forValueHowFrom
Span LengthL_spanwants m/mm55'-0"; 82'-0"; 55'-0" ft-inRead as the left, middle, and right bridge span dimensions: 55'-0", 82'-0", and 55'-0".The elevation shows the longitudinal girder profile across the three bridge spans. The dimensions are labelled as bridge spans rather than explicitly as girder spans; they are therefore treated as the girder support-to-support spans with low confidence.readcheckp1 · p01_r08
Cross-sectional AreaAwants m2/mm2not establishedNo longitudinal girder cross-section dimensions or stated sectional area are provided in the elevation.not found
Instance CountNwants countnot establishedThe longitudinal girder object note states that the individual girder quantity is not shown in this elevation.not found
Material TypeMATnot establishedNo material is stated for the longitudinal girder.not found
MassMwants kg/tnot establishedNo longitudinal girder mass, unit weight, material density, or sufficient dimensions for mass calculation are provided.not found

Worked out by openai/gpt-5.6-terra-pro from the readings below, which are the source. A derived value shows its arithmetic — check it against the drawing before it is priced.

Notes on the sheets that carry it

  • p1CHAIN LINK WIRE FENCE, TYP.
  • p1FRONT FACE OF WALL NO. 1
  • p1FRONT FACE OF WALL NO. 2
  • p1FUTURE GROUNDLINE
  • p1APPROXIMATE EXISTING GROUNDLINE
  • p1℄ FUTURE ACCESS ROAD
  • p1℄ EXISTING TRACK
  • p1℄ FUTURE TRACK

Every crop it was read in — the drawing beside what the model took off it

Page 1

crop

p01_r08

page 1 · bridge_bents_and_girders_p01_r08
Original
p01_r08
{
  "view": "Elevation",
  "objects": [
    {
      "name": "bridge deck slab",
      "tag": "",
      "shape": "longitudinal rectangular slab",
      "material": "",
      "count": 1,
      "note": "Continuous across the bridge elevation."
    },
    {
      "name": "longitudinal girder",
      "tag": "",
      "shape": "longitudinal rectangular member",
      "material": "",
      "count": null,
      "note": "Individual girder quantity is not shown in this elevation."
    },
    {
      "name": "interior pier bent",
      "tag": "BENT 2 **; BENT 3 **",
      "shape": "single rectangular column with cap",
      "material": "",
      "count": 2,
      "note": "Each visible bent is supported on a pile cap."
    },
    {
      "name": "end bent",
      "tag": "B.F.P.R. BENT 1 **; B.F.P.R. BENT 4 **",
      "shape": "",
      "material": "",
      "count": 2,
      "note": "Shown at the respective bridge ends."
    },
    {
      "name": "pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 2,
      "note": "One shown below each interior pier bent."
    },
    {
      "name": "pile",
      "tag": "",
      "shape": "vertical slender member",
      "material": "",
      "count": 6,
      "note": "Three piles are visibly drawn below each interior pile cap."
    },
    {
      "name": "wall",
      "tag": "WALL NO. 1; WALL NO. 2",
      "shape": "vertical",
      "material": "",
      "count": 2,
      "note": "Only the front faces are called out."
    },
    {
      "name": "bearing",
      "tag": "FIX",
      "shape": "rectangular support block",
      "material": "",
      "count": 2,
      "note": "Shown at Bent 2."
    },
    {
      "name": "bearing",
      "tag": "EXP.",
      "shape": "rectangular support block",
      "material": "",
      "count": 4,
      "note": "Shown at the end supports and at Bent 3."
    },
    {
      "name": "chain link wire fence",
      "tag": "",
      "shape": "rectangular mesh panel",
      "material": "chain link wire",
      "count": 3,
      "note": "Typical."
    }
  ],
  "measurements": [
    {
      "label": "TOTAL LENGTH OF BRIDGE",
      "value": "192'-0\" ***",
      "unit": "",
      "appliesTo": "bridge"
    },
    {
      "label": "",
      "value": "55'-0\" ***",
      "unit": "",
      "appliesTo": "left bridge span"
    },
    {
      "label": "",
      "value": "82'-0\" ***",
      "unit": "",
      "appliesTo": "middle bridge span"
    },
    {
      "label": "",
      "value": "55'-0\" ***",
      "unit": "",
      "appliesTo": "right bridge span"
    },
    {
      "label": "EL.",
      "value": "151.00",
      "unit": "",
      "appliesTo": "typical elevation"
    }
  ],
  "notes": [
    "CHAIN LINK WIRE FENCE, TYP.",
    "FRONT FACE OF WALL NO. 1",
    "FRONT FACE OF WALL NO. 2",
    "FUTURE GROUNDLINE",
    "APPROXIMATE EXISTING GROUNDLINE",
    "℄ FUTURE ACCESS ROAD",
    "℄ EXISTING TRACK",
    "℄ FUTURE TRACK"
  ],
  "labels": [
    "PGL",
    "ELEVATION"
  ],
  "description": "This crop is a longitudinal elevation of a three-span bridge, showing the deck and longitudinal girder profile over two interior pier bents and end bents. It documents span lengths, bearing designations, pile-supported interior foundations, wall-face callouts, fencing, and the indicated existing and future ground and track/access-road centerlines."
}

p01_r08Elevation

  • longitudinal girderlongitudinal rectangular memberIndividual girder quantity is not shown in this elevation.

192'-0" *** TOTAL LENGTH OF BRIDGE55'-0" ***82'-0" ***55'-0" ***151.00 EL.