Drawing to BOQpipeline control sheet
← Mindmapwhat the drawings said

Filter Media

1 page · 4 crops · ×6 · drainage

Matched toGranular Filter Layerbridge.drainage_protection_system.filter_layeron “Filter Media”

1 read off the drawings · 3 not established
The class asks forValueHowFrom
LengthLwants m/mmnot establishedThe readings identify filter media and state its thickness only. No dimension establishes the filter-media length.not found
WidthWwants m/mmnot establishedThe readings identify filter media and state its thickness only. No dimension establishes the filter-media width.not found
Layer ThicknessT_layerwants m/mm600 mmRead directly as “600 THK. FILTER MEDIA.”Each cited reading explicitly assigns a 600-thick dimension to the filter media; the elevation reading states the unit as mm.readp2 · p02_r05p2 · p02_r01p2 · p02_r01 elevation of bridge superstructurep2 · p02_r05 section a a
Material TypeMATnot establishedThe item is labelled “FILTER MEDIA,” but no constituent material, grading, or specified material type is stated in the readings.not found

Worked out by openai/gpt-5.6-terra-pro from the readings below, which are the source. A derived value shows its arithmetic — check it against the drawing before it is priced.

Every dimension read for it16

  • 600 THK.filter media thicknessp2 · p02_r05
  • 40000(SQ) 46188(SK) mmHorizontal dimensionnot attributedp2 · p02_r01
  • 46000(SK) 46188(SK) mmHorizontal dimensionnot attributedp2 · p02_r01
  • 37761(SQ) 43602(SK) mmHorizontal dimensionnot attributedp2 · p02_r01
  • 37761(SQ) 43602(SK) mmHorizontal dimensionnot attributedp2 · p02_r01
  • 1200 (min.) mmMinimum vertical distance to HFLnot attributedp2 · p02_r01
  • 506.000m mLWLnot attributedp2 · p02_r01
  • 600 mmFilter media thicknessp2 · p02_r01
  • 40000(SQ) 46188(SK)span dimensionnot attributedp2 · p02_r01 elevation of bridge superstructure
  • 46000(SK) 46188(SK)span dimensionnot attributedp2 · p02_r01 elevation of bridge superstructure
  • 37761(SQ) 43602(SK)bridge dimensionnot attributedp2 · p02_r01 elevation of bridge superstructure
  • 37761(SQ) 43602(SK)bridge dimensionnot attributedp2 · p02_r01 elevation of bridge superstructure
  • 600 THK.filter media thicknessp2 · p02_r01 elevation of bridge superstructure
  • 1200 mmHFLnot attributedp2 · p02_r01 elevation of bridge superstructure
  • 506.000 mLWLnot attributedp2 · p02_r01 elevation of bridge superstructure
  • 600 THK.filter media thicknessp2 · p02_r05 section a a

Notes on the sheets that carry it

  • p2POT-PTFE BEARING (TYP.)
  • p2RCC SEISMIC STOPPER
  • p2STONE PITCHING
  • p2INDEPENDENT RETAINING WALL
  • p2600 THK. FILTER MEDIA
  • p21200 DIA BORED CAST-IN-SITU PILES
  • p2300 THK. APPROACH SLAB
  • p2150 THK. PCC LEVELING COURSE
  • p2RCC CRASH BARRIER
  • p2LAUNCHING APRON
  • p2RCC COLUMN PIER (TYP.)
  • p2DECK CONTINUITY
  • p2PRECAST PSC GIRDER (TYP.)
  • p2WALL TYPE ABUTMENT
  • p21200φ RCC CAST IN SITU PILE (TYP.)
  • p21. ALL DIMENSIONS ARE IN MILL... OTHERWISE SPECIFIED.
  • p22. DIMENSIONS ARE NOT TO BE ... FOLLOWED.
  • p23. THIS DRAWING SHALL BE RE... ALIGNMENT DRAWINGS.
  • p24. THE BRIDGE HAS BEEN DES... CLASS 70R + TWO LANE OF 70R OR SV LOADING WHICH...
  • p25. GRADE OF CONCRETE FOR VA... FOLLOWS:-
  • p2• PSC PRECAST GIRDER -
  • p2• R.C.C. CAST IN SITU DEC...
  • p2• R.C.C. END CROSS GIRDER -
  • p2• R.C.C. INTERMEDIATE CROS...
  • p2• BEARING PEDESTAL -
  • p21. ALL DIMENSIONS ARE IN M
  • p2OTHERWISE SPECIFIED.
  • p23. THIS DRAWING SHALL BE RE
  • p2ALIGNMENT DRAWINGS.
  • p24. THE BRIDGE HAS BEEN DES
  • p2CLASS 70R + TWO LANE O
  • p270R OR SV LOADING WHICH
  • p25. GRADE OF CONCRETE FOR
  • p2FOLLOWS:-
  • p2• R.C.C. CAST IN SITU DE
  • p2• R.C.C. INTERMEDIATE C
  • p2• REINFORCEMENT

Every crop it was read in — the drawing beside what the model took off it

Page 2

crop

p02_r05

page 2 · abutment_and_retaining_wall_p02_r05
Original
p02_r05
{
  "view": "Section",
  "objects": [
    {
      "name": "Abutment",
      "tag": "A2",
      "shape": "rectangular stem and footing",
      "material": "",
      "count": 1,
      "note": "Shown supporting the bridge end at the expansion joint."
    },
    {
      "name": "Bridge deck slab",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 1,
      "note": ""
    },
    {
      "name": "Bridge girder",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 1,
      "note": "Only a partial girder/end portion is visible at left."
    },
    {
      "name": "Expansion joint",
      "tag": "",
      "shape": "linear joint",
      "material": "",
      "count": 1,
      "note": "At bridge centreline/end of deck."
    },
    {
      "name": "Bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "PTFE",
      "count": 1,
      "note": "Called out as POT-PTFE BEARING (TYP.)."
    },
    {
      "name": "Seismic stopper",
      "tag": "",
      "shape": "rectangular",
      "material": "RCC",
      "count": 1,
      "note": ""
    },
    {
      "name": "Pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 1,
      "note": "Dashed outline beneath the abutment."
    },
    {
      "name": "Bored cast-in-situ pile",
      "tag": "",
      "shape": "circular",
      "material": "",
      "count": 4,
      "note": "Pile positions are shown below the pile cap."
    },
    {
      "name": "Independent retaining wall",
      "tag": "",
      "shape": "vertical rectangular wall",
      "material": "",
      "count": 1,
      "note": "Located to the right of the abutment."
    },
    {
      "name": "Stone pitching",
      "tag": "",
      "shape": "irregular pitched surface",
      "material": "stone",
      "count": 1,
      "note": "Shown at the retaining-wall side."
    },
    {
      "name": "Filter media",
      "tag": "",
      "shape": "irregular zone",
      "material": "",
      "count": 1,
      "note": "Behind/below the stone pitching."
    },
    {
      "name": "Embankment",
      "tag": "",
      "shape": "sloping",
      "material": "",
      "count": 1,
      "note": "Slope marked 1 vertical to 2 horizontal."
    }
  ],
  "measurements": [
    {
      "label": "offset to C OF BRG.",
      "value": "1070 (SQ.)",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "offset to C OF BRG.",
      "value": "1236 (SK.)",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "EXP.GAP",
      "value": "80(SQ.)",
      "unit": "",
      "appliesTo": "Expansion joint"
    },
    {
      "label": "EXP.GAP",
      "value": "92(SK)",
      "unit": "",
      "appliesTo": "Expansion joint"
    },
    {
      "label": "deck/slab vertical dimension",
      "value": "230",
      "unit": "",
      "appliesTo": "Bridge deck slab"
    },
    {
      "label": "vertical dimension",
      "value": "2650",
      "unit": "",
      "appliesTo": "Bridge girder"
    },
    {
      "label": "horizontal dimension",
      "value": "1500",
      "unit": "",
      "appliesTo": "Bridge girder"
    },
    {
      "label": "horizontal dimension",
      "value": "2850",
      "unit": "",
      "appliesTo": "Bridge girder"
    },
    {
      "label": "horizontal dimension",
      "value": "3500(SQ)",
      "unit": "",
      "appliesTo": "Bridge deck slab"
    },
    {
      "label": "horizontal dimension",
      "value": "1500",
      "unit": "",
      "appliesTo": "Abutment"
    },
    {
      "label": "pile spacing/end offset",
      "value": "750",
      "unit": "",
      "appliesTo": "Bored cast-in-situ piles"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "Bored cast-in-situ piles"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "Bored cast-in-situ piles"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "Bored cast-in-situ piles"
    },
    {
      "label": "pile spacing/end offset",
      "value": "750",
      "unit": "",
      "appliesTo": "Bored cast-in-situ piles"
    },
    {
      "label": "pile cap length",
      "value": "12300",
      "unit": "",
      "appliesTo": "Pile cap"
    },
    {
      "label": "embankment slope",
      "value": "1:2",
      "unit": "",
      "appliesTo": "Embankment"
    },
    {
      "label": "filter media thickness",
      "value": "600",
      "unit": "THK.",
      "appliesTo": "Filter media"
    },
    {
      "label": "pile diameter",
      "value": "1200",
      "unit": "DIA",
      "appliesTo": "Bored cast-in-situ piles"
    },
    {
      "label": "scale",
      "value": "1:150",
      "unit": "",
      "appliesTo": "SECTION A-A"
    }
  ],
  "notes": [
    "POT-PTFE BEARING (TYP.)",
    "RCC SEISMIC STOPPER",
    "STONE PITCHING",
    "INDEPENDENT RETAINING WALL",
    "600 THK. FILTER MEDIA",
    "1200 DIA BORED CAST-IN-SITU PILES"
  ],
  "labels": [
    "A2",
    "C OF EXP. JOINT",
    "C OF BRG.",
    "SECTION A-A",
    "(SCALE 1:150)"
  ],
  "description": "This crop shows SECTION A-A through abutment A2 at the bridge expansion-joint end. It documents the deck end, bearing and RCC seismic stopper, abutment and piled foundation, together with the adjacent sloping embankment and independent retaining wall treatment."
}

p02_r05Section

  • Filter media×1irregular zoneBehind/below the stone pitching.

1070 (SQ.) offset to C OF BRG.1236 (SK.) offset to C OF BRG.80(SQ.) EXP.GAP92(SK) EXP.GAP230 deck/slab vertical dimension2650 vertical dimension1500 horizontal dimension2850 horizontal dimension+12 more

crop

p02_r01

page 2 · bridge_superstructure_p02_r01
Original
p02_r01
{
  "view": "Elevation",
  "objects": [
    {
      "name": "Wall type abutment",
      "tag": "A1",
      "shape": "rectangular wall",
      "material": "",
      "count": 1,
      "note": "Left abutment shown."
    },
    {
      "name": "Wall type abutment",
      "tag": "A2",
      "shape": "rectangular wall",
      "material": "",
      "count": 1,
      "note": "Right abutment shown."
    },
    {
      "name": "RCC column pier",
      "tag": "P1",
      "shape": "rectangular column",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Marked “(TYP.)”."
    },
    {
      "name": "Precast PSC girder",
      "tag": "",
      "shape": "rectangular elevation profile",
      "material": "precast PSC",
      "count": 6,
      "note": "Marked “(TYP.)”; three girders are visible in each span."
    },
    {
      "name": "RCC crash barrier",
      "tag": "",
      "shape": "continuous linear barrier",
      "material": "reinforced concrete",
      "count": null,
      "note": "Shown along the deck."
    },
    {
      "name": "POT-PTFE bearing",
      "tag": "FR",
      "shape": "rectangular",
      "material": "",
      "count": 3,
      "note": "Marked “(TYP.)” at abutment locations."
    },
    {
      "name": "POT-PTFE bearing",
      "tag": "FX",
      "shape": "rectangular",
      "material": "",
      "count": 1,
      "note": "Shown at the pier."
    },
    {
      "name": "Deck continuity",
      "tag": "",
      "shape": "rectangular joint/diaphragm",
      "material": "",
      "count": 1,
      "note": "Shown over pier P1."
    },
    {
      "name": "Approach slab",
      "tag": "",
      "shape": "sloping rectangular slab",
      "material": "",
      "count": 2,
      "note": "One at each end of bridge."
    },
    {
      "name": "PCC levelling course",
      "tag": "",
      "shape": "horizontal layer",
      "material": "PCC",
      "count": 2,
      "note": "Below approach slabs."
    },
    {
      "name": "Launching apron",
      "tag": "",
      "shape": "sloping and horizontal apron",
      "material": "",
      "count": 2,
      "note": "One adjacent to each abutment."
    },
    {
      "name": "Stone pitching",
      "tag": "",
      "shape": "sloping protection layer",
      "material": "stone",
      "count": 2,
      "note": "At both abutments."
    },
    {
      "name": "Independent retaining wall",
      "tag": "",
      "shape": "vertical wall",
      "material": "",
      "count": 2,
      "note": "One behind each abutment."
    },
    {
      "name": "Filter media",
      "tag": "",
      "shape": "layer",
      "material": "",
      "count": 2,
      "note": "Marked 600 THK."
    },
    {
      "name": "Pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 3,
      "note": "One under each abutment and one under pier P1."
    },
    {
      "name": "RCC cast in situ pile",
      "tag": "",
      "shape": "circular pile",
      "material": "reinforced concrete",
      "count": 8,
      "note": "Marked “(TYP.)”; three visible below each abutment cap and two below pier cap."
    }
  ],
  "measurements": [
    {
      "label": "Expansion gap",
      "value": "80(SQ.) 92(SK)",
      "unit": "mm",
      "appliesTo": "A1"
    },
    {
      "label": "Expansion gap",
      "value": "80(SQ.) 92(SK)",
      "unit": "mm",
      "appliesTo": "A2"
    },
    {
      "label": "Horizontal dimension",
      "value": "40000(SQ) 46188(SK)",
      "unit": "mm",
      "appliesTo": ""
    },
    {
      "label": "Horizontal dimension",
      "value": "46000(SK) 46188(SK)",
      "unit": "mm",
      "appliesTo": ""
    },
    {
      "label": "Horizontal dimension",
      "value": "37761(SQ) 43602(SK)",
      "unit": "mm",
      "appliesTo": ""
    },
    {
      "label": "Horizontal dimension",
      "value": "37761(SQ) 43602(SK)",
      "unit": "mm",
      "appliesTo": ""
    },
    {
      "label": "Distance from C OF BRG.",
      "value": "1070(SQ) 1236(SK)",
      "unit": "mm",
      "appliesTo": "A1"
    },
    {
      "label": "Distance from C OF BRG.",
      "value": "1070(SQ) 1236(SK)",
      "unit": "mm",
      "appliesTo": "A2"
    },
    {
      "label": "Distance at pier",
      "value": "1170(SQ) 1350(SK)",
      "unit": "mm",
      "appliesTo": "P1"
    },
    {
      "label": "Distance at pier",
      "value": "1170(SQ) 1350(SK)",
      "unit": "mm",
      "appliesTo": "P1"
    },
    {
      "label": "Approach slab thickness",
      "value": "300",
      "unit": "mm",
      "appliesTo": "A1, A2"
    },
    {
      "label": "PCC levelling course thickness",
      "value": "150",
      "unit": "mm",
      "appliesTo": "A1, A2"
    },
    {
      "label": "Minimum vertical distance to HFL",
      "value": "1200 (min.)",
      "unit": "mm",
      "appliesTo": ""
    },
    {
      "label": "LWL",
      "value": "506.000m",
      "unit": "m",
      "appliesTo": ""
    },
    {
      "label": "Filter media thickness",
      "value": "600",
      "unit": "mm",
      "appliesTo": "Filter media"
    },
    {
      "label": "Abutment pile-cap end projection",
      "value": "750",
      "unit": "mm",
      "appliesTo": "Pile cap"
    },
    {
      "label": "Abutment pile spacing",
      "value": "3600",
      "unit": "mm",
      "appliesTo": "Pile cap"
    },
    {
      "label": "Abutment pile-cap overall width",
      "value": "12300",
      "unit": "mm",
      "appliesTo": "Pile cap"
    },
    {
      "label": "Pier pile-cap end projection",
      "value": "750",
      "unit": "mm",
      "appliesTo": "P1"
    },
    {
      "label": "Pier pile spacing",
      "value": "3600",
      "unit": "mm",
      "appliesTo": "P1"
    },
    {
      "label": "Pier pile-cap overall width",
      "value": "5100",
      "unit": "mm",
      "appliesTo": "P1"
    },
    {
      "label": "Cast in situ pile diameter",
      "value": "1200φ",
      "unit": "mm",
      "appliesTo": "RCC cast in situ pile"
    },
    {
      "label": "Chainage LHS",
      "value": "64+360.197",
      "unit": "km.",
      "appliesTo": "A1"
    },
    {
      "label": "Chainage RHS",
      "value": "64+371.487",
      "unit": "km.",
      "appliesTo": "A1"
    },
    {
      "label": "FRL LHS",
      "value": "518.281",
      "unit": "m",
      "appliesTo": "A1"
    },
    {
      "label": "FRL RHS",
      "value": "518.465",
      "unit": "m",
      "appliesTo": "A1"
    },
    {
      "label": "Ground level LHS",
      "value": "509.560",
      "unit": "m",
      "appliesTo": "A1"
    },
    {
      "label": "Ground level RHS",
      "value": "509.155",
      "unit": "m",
      "appliesTo": "A1"
    },
    {
      "label": "Chainage LHS",
      "value": "64+406.385",
      "unit": "km.",
      "appliesTo": "P1"
    },
    {
      "label": "Chainage RHS",
      "value": "64+417.675",
      "unit": "km.",
      "appliesTo": "P1"
    },
    {
      "label": "FRL LHS",
      "value": "519.033",
      "unit": "m",
      "appliesTo": "P1"
    },
    {
      "label": "FRL RHS",
      "value": "519.217",
      "unit": "m",
      "appliesTo": "P1"
    },
    {
      "label": "Ground level LHS",
      "value": "503.816",
      "unit": "m",
      "appliesTo": "P1"
    },
    {
      "label": "Ground level RHS",
      "value": "503.883",
      "unit": "m",
      "appliesTo": "P1"
    },
    {
      "label": "Chainage LHS",
      "value": "64+452.573",
      "unit": "km.",
      "appliesTo": "A2"
    },
    {
      "label": "Chainage RHS",
      "value": "64+463.814",
      "unit": "km.",
      "appliesTo": "A2"
    },
    {
      "label": "FRL LHS",
      "value": "519.785",
      "unit": "m",
      "appliesTo": "A2"
    },
    {
      "label": "FRL RHS",
      "value": "519.968",
      "unit": "m",
      "appliesTo": "A2"
    },
    {
      "label": "Ground level LHS",
      "value": "511.891",
      "unit": "m",
      "appliesTo": "A2"
    },
    {
      "label": "Ground level RHS",
      "value": "512.668",
      "unit": "m",
      "appliesTo": "A2"
    },
    {
      "label": "Drawing scale",
      "value": "1:300",
      "unit": "",
      "appliesTo": "Elevation"
    }
  ],
  "notes": [
    "300 THK. APPROACH SLAB",
    "150 THK. PCC LEVELING COURSE",
    "RCC CRASH BARRIER",
    "POT-PTFE BEARING (TYP.)",
    "LAUNCHING APRON",
    "STONE PITCHING",
    "INDEPENDENT RETAINING WALL",
    "600 THK. FILTER MEDIA",
    "RCC COLUMN PIER (TYP.)",
    "DECK CONTINUITY",
    "PRECAST PSC GIRDER (TYP.)",
    "WALL TYPE ABUTMENT",
    "1200φ RCC CAST IN SITU PILE (TYP.)",
    "1. ALL DIMENSIONS ARE IN MILL... OTHERWISE SPECIFIED.",
    "2. DIMENSIONS ARE NOT TO BE ... FOLLOWED.",
    "3. THIS DRAWING SHALL BE RE... ALIGNMENT DRAWINGS.",
    "4. THE BRIDGE HAS BEEN DES... CLASS 70R + TWO LANE OF 70R OR SV LOADING WHICH...",
    "5. GRADE OF CONCRETE FOR VA... FOLLOWS:-",
    "• PSC PRECAST GIRDER -",
    "• R.C.C. CAST IN SITU DEC...",
    "• R.C.C. END CROSS GIRDER -",
    "• R.C.C. INTERMEDIATE CROS...",
    "• BEARING PEDESTAL -"
  ],
  "labels": [
    "TO DEWAS",
    "TO KHANDWA",
    "C OF EXP. JOINT",
    "C OF BRG.",
    "HFL=",
    "LWL=506.000m",
    "CHAINAGE IN (km.)",
    "LHS",
    "RHS",
    "FRL. (m)",
    "MAIN CARRIAGEWAY",
    "GROUND LEVEL (m)",
    "ELEVATION",
    "(SCALE 1:300)",
    "NOTES:"
  ],
  "description": "This crop is an elevation of a bridge superstructure and its supporting substructure, extending between abutments A1 and A2 with pier P1 at the centre. It shows PSC girders, bearings, deck barriers, approach arrangements, abutment and pier foundations, retaining walls, stone pitching, and an elevation/chainage table."
}

p02_r01Elevation

  • Filter media×2layerMarked 600 THK.

80(SQ.) 92(SK) mm Expansion gap80(SQ.) 92(SK) mm Expansion gap40000(SQ) 46188(SK) mm Horizontal dimension46000(SK) 46188(SK) mm Horizontal dimension37761(SQ) 43602(SK) mm Horizontal dimension37761(SQ) 43602(SK) mm Horizontal dimension1070(SQ) 1236(SK) mm Distance from C OF BRG.1070(SQ) 1236(SK) mm Distance from C OF BRG.+33 more

crop

p02_r01 elevation of bridge superstructure

page 2 · structural_drawings_pkg_1_7a22288d85c64bc6bd8c641faee2f453_p02_r01_elevation_of_bridge_superstructure
Original
p02_r01 elevation of bridge superstructure
{
  "view": "Elevation",
  "objects": [
    {
      "name": "wall type abutment",
      "tag": "A1",
      "shape": "rectangular with sloping wingwall/return wall",
      "material": "",
      "count": 1,
      "note": "Left abutment."
    },
    {
      "name": "wall type abutment",
      "tag": "A2",
      "shape": "rectangular with sloping wingwall/return wall",
      "material": "",
      "count": 1,
      "note": "Right abutment."
    },
    {
      "name": "RCC column pier",
      "tag": "P1",
      "shape": "rectangular column",
      "material": "reinforced concrete",
      "count": 1,
      "note": "Marked RCC COLUMN PIER (TYP.)."
    },
    {
      "name": "precast PSC girder",
      "tag": "",
      "shape": "girder",
      "material": "precast prestressed concrete",
      "count": null,
      "note": "Marked PRECAST PSC GIRDER (TYP.)."
    },
    {
      "name": "POT-PTFE bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 4,
      "note": "Marked POT-PTFE BEARING (TYP.)."
    },
    {
      "name": "RCC crash barrier",
      "tag": "",
      "shape": "linear barrier",
      "material": "reinforced concrete",
      "count": 2,
      "note": ""
    },
    {
      "name": "deck continuity",
      "tag": "",
      "shape": "linear deck connection",
      "material": "",
      "count": 1,
      "note": ""
    },
    {
      "name": "expansion joint",
      "tag": "",
      "shape": "linear joint",
      "material": "",
      "count": 2,
      "note": "Located at the two abutment ends."
    },
    {
      "name": "approach slab",
      "tag": "",
      "shape": "sloping slab",
      "material": "",
      "count": 2,
      "note": "Marked 300 THK. APPROACH SLAB."
    },
    {
      "name": "PCC levelling course",
      "tag": "",
      "shape": "horizontal layer",
      "material": "plain cement concrete",
      "count": 2,
      "note": "Marked 150 THK. PCC LEVELLING COURSE."
    },
    {
      "name": "independent retaining wall",
      "tag": "",
      "shape": "sloping wall",
      "material": "",
      "count": 2,
      "note": ""
    },
    {
      "name": "stone pitching",
      "tag": "",
      "shape": "sloping surface protection",
      "material": "stone",
      "count": 2,
      "note": "Associated with 600 THK. FILTER MEDIA."
    },
    {
      "name": "filter media",
      "tag": "",
      "shape": "layer",
      "material": "",
      "count": 2,
      "note": "Marked 600 THK. FILTER MEDIA."
    },
    {
      "name": "pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 3,
      "note": "Two abutment pile caps and one pier pile cap are visible."
    },
    {
      "name": "RCC cast in situ pile",
      "tag": "",
      "shape": "circular",
      "material": "reinforced concrete",
      "count": 10,
      "note": "Marked 1200ø RCC CAST IN SITU PILE (TYP.)."
    }
  ],
  "measurements": [
    {
      "label": "span dimension",
      "value": "40000(SQ) 46188(SK)",
      "unit": "",
      "appliesTo": ""
    },
    {
      "label": "span dimension",
      "value": "46000(SK) 46188(SK)",
      "unit": "",
      "appliesTo": ""
    },
    {
      "label": "bridge dimension",
      "value": "37761(SQ) 43602(SK)",
      "unit": "",
      "appliesTo": ""
    },
    {
      "label": "bridge dimension",
      "value": "37761(SQ) 43602(SK)",
      "unit": "",
      "appliesTo": ""
    },
    {
      "label": "EXP.GAP",
      "value": "80(SQ.) 92(SK)",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "EXP.GAP",
      "value": "80(SQ.) 92(SK)",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "dimension",
      "value": "1070(SQ) 1236(SK)",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "dimension",
      "value": "1170(SQ) 1350(SK)",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "dimension",
      "value": "1170(SQ) 1350(SK)",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "dimension",
      "value": "1070(SQ) 1236(SK)",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "approach slab thickness",
      "value": "300",
      "unit": "THK.",
      "appliesTo": "approach slab"
    },
    {
      "label": "PCC levelling course thickness",
      "value": "150",
      "unit": "THK.",
      "appliesTo": "PCC levelling course"
    },
    {
      "label": "filter media thickness",
      "value": "600",
      "unit": "THK.",
      "appliesTo": "filter media"
    },
    {
      "label": "HFL",
      "value": "1200",
      "unit": "mm",
      "appliesTo": ""
    },
    {
      "label": "LWL",
      "value": "506.000",
      "unit": "m",
      "appliesTo": ""
    },
    {
      "label": "pile diameter",
      "value": "1200ø",
      "unit": "",
      "appliesTo": "RCC cast in situ pile"
    },
    {
      "label": "pile cap end dimension",
      "value": "750",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "pile cap overall dimension",
      "value": "12300",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "pile cap end dimension",
      "value": "750",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "pile cap end dimension",
      "value": "750",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "pile cap overall dimension",
      "value": "5100",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "pile cap end dimension",
      "value": "750",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "pile cap end dimension",
      "value": "750",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "pile cap overall dimension",
      "value": "12300",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "pile cap end dimension",
      "value": "750",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "chainage LHS",
      "value": "64+360.197",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "chainage RHS",
      "value": "64+371.487",
      "unit": "",
      "appliesTo": "A1"
    },
    {
      "label": "FRL main carriageway LHS",
      "value": "518.281",
      "unit": "m",
      "appliesTo": "A1"
    },
    {
      "label": "FRL main carriageway RHS",
      "value": "518.465",
      "unit": "m",
      "appliesTo": "A1"
    },
    {
      "label": "ground level main carriageway LHS",
      "value": "509.560",
      "unit": "m",
      "appliesTo": "A1"
    },
    {
      "label": "ground level main carriageway RHS",
      "value": "509.155",
      "unit": "m",
      "appliesTo": "A1"
    },
    {
      "label": "chainage",
      "value": "64+406.385",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "chainage",
      "value": "64+417.675",
      "unit": "",
      "appliesTo": "P1"
    },
    {
      "label": "FRL main carriageway",
      "value": "519.033",
      "unit": "m",
      "appliesTo": "P1"
    },
    {
      "label": "FRL main carriageway",
      "value": "519.217",
      "unit": "m",
      "appliesTo": "P1"
    },
    {
      "label": "ground level main carriageway",
      "value": "503.816",
      "unit": "m",
      "appliesTo": "P1"
    },
    {
      "label": "ground level main carriageway",
      "value": "503.883",
      "unit": "m",
      "appliesTo": "P1"
    },
    {
      "label": "chainage LHS",
      "value": "64+452.573",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "chainage RHS",
      "value": "64+463.814",
      "unit": "",
      "appliesTo": "A2"
    },
    {
      "label": "FRL main carriageway LHS",
      "value": "519.785",
      "unit": "m",
      "appliesTo": "A2"
    },
    {
      "label": "FRL main carriageway RHS",
      "value": "519.968",
      "unit": "m",
      "appliesTo": "A2"
    },
    {
      "label": "ground level main carriageway LHS",
      "value": "511.891",
      "unit": "m",
      "appliesTo": "A2"
    },
    {
      "label": "ground level main carriageway RHS",
      "value": "512.668",
      "unit": "m",
      "appliesTo": "A2"
    },
    {
      "label": "drawing scale",
      "value": "1:300",
      "unit": "",
      "appliesTo": "ELEVATION"
    }
  ],
  "notes": [
    "1. ALL DIMENSIONS ARE IN M",
    "OTHERWISE SPECIFIED.",
    "2. DIMENSIONS ARE NOT TO BE FOLLOWED.",
    "3. THIS DRAWING SHALL BE RE",
    "ALIGNMENT DRAWINGS.",
    "4. THE BRIDGE HAS BEEN DES",
    "CLASS 70R + TWO LANE O",
    "70R OR SV LOADING WHICH",
    "5. GRADE OF CONCRETE FOR",
    "FOLLOWS:-",
    "• PSC PRECAST GIRDER",
    "• R.C.C. CAST IN SITU DE",
    "• R.C.C. END CROSS GIRDER",
    "• R.C.C. INTERMEDIATE C",
    "• REINFORCEMENT"
  ],
  "labels": [
    "TO DEWAS",
    "TO KHANDWA",
    "C OF EXP. JOINT",
    "C OF BRG.",
    "FR",
    "ELEVATION",
    "(SCALE 1:300)",
    "CHAINAGE IN (km.)",
    "LHS",
    "RHS",
    "FRL. (m) MAIN CARRIAGEWAY",
    "GROUND LEVEL (m) MAIN CARRIAGEWAY",
    "NOTES:"
  ],
  "description": "This crop shows an elevation of a two-span bridge between abutments A1 and A2, with central RCC column pier P1. It documents the superstructure, bearings, approach slabs, abutment and retaining-wall protection, pile foundations, water levels, and chainage/elevation data."
}

p02_r01 elevation of bridge superstructureElevation

  • filter media×2layerMarked 600 THK. FILTER MEDIA.

40000(SQ) 46188(SK) span dimension46000(SK) 46188(SK) span dimension37761(SQ) 43602(SK) bridge dimension37761(SQ) 43602(SK) bridge dimension80(SQ.) 92(SK) EXP.GAP80(SQ.) 92(SK) EXP.GAP1070(SQ) 1236(SK) dimension1170(SQ) 1350(SK) dimension+43 more

crop

p02_r05 section a a

page 2 · structural_drawings_pkg_1_7a22288d85c64bc6bd8c641faee2f453_p02_r05_section_a_a
Original
p02_r05 section a a
{
  "view": "Section",
  "objects": [
    {
      "name": "bridge deck slab",
      "tag": "",
      "shape": "rectangular horizontal slab",
      "material": "",
      "count": 1,
      "note": "Partial deck section is shown."
    },
    {
      "name": "expansion joint",
      "tag": "",
      "shape": "narrow vertical joint",
      "material": "",
      "count": 1,
      "note": "Located at C OF EXP. JOINT."
    },
    {
      "name": "abutment",
      "tag": "",
      "shape": "reinforced concrete wall with seat",
      "material": "",
      "count": 1,
      "note": "Supported on a pile cap."
    },
    {
      "name": "wingwall",
      "tag": "",
      "shape": "sloping retaining wall",
      "material": "",
      "count": 1,
      "note": "Extends from the abutment toward the left."
    },
    {
      "name": "pile cap",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 1,
      "note": "Shown below the abutment."
    },
    {
      "name": "bored cast-in-situ piles",
      "tag": "",
      "shape": "circular",
      "material": "",
      "count": 4,
      "note": "Pile locations are shown beneath the pile cap."
    },
    {
      "name": "POT-PTFE bearing",
      "tag": "",
      "shape": "rectangular",
      "material": "",
      "count": 1,
      "note": "Marked TYP."
    },
    {
      "name": "RCC seismic stopper",
      "tag": "",
      "shape": "rectangular block",
      "material": "RCC",
      "count": 1,
      "note": ""
    },
    {
      "name": "independent retaining wall",
      "tag": "",
      "shape": "vertical wall",
      "material": "",
      "count": 1,
      "note": "Partially shown at the right side of the section."
    },
    {
      "name": "stone pitching",
      "tag": "",
      "shape": "sloping layer",
      "material": "stone",
      "count": 1,
      "note": ""
    },
    {
      "name": "filter media",
      "tag": "",
      "shape": "tapered layer",
      "material": "",
      "count": 1,
      "note": "Shown adjacent to the independent retaining wall."
    },
    {
      "name": "reinforcement bar",
      "tag": "1",
      "shape": "bent bar",
      "material": "",
      "count": 1,
      "note": "Bar mark is shown within the sloping wall."
    },
    {
      "name": "reinforcement bar",
      "tag": "2",
      "shape": "bent bar",
      "material": "",
      "count": 1,
      "note": "Bar mark is shown within the sloping wall."
    }
  ],
  "measurements": [
    {
      "label": "dimension (SQ.)",
      "value": "1070",
      "unit": "",
      "appliesTo": "C OF BRG."
    },
    {
      "label": "dimension (SK.)",
      "value": "1236",
      "unit": "",
      "appliesTo": "C OF BRG."
    },
    {
      "label": "EXP.GAP (SQ.)",
      "value": "80",
      "unit": "",
      "appliesTo": "expansion joint"
    },
    {
      "label": "EXP.GAP (SK)",
      "value": "92",
      "unit": "",
      "appliesTo": "expansion joint"
    },
    {
      "label": "dimension (SQ)",
      "value": "3500",
      "unit": "",
      "appliesTo": "deck/abutment section"
    },
    {
      "label": "vertical dimension",
      "value": "230",
      "unit": "",
      "appliesTo": "deck end"
    },
    {
      "label": "vertical dimension",
      "value": "2650",
      "unit": "",
      "appliesTo": "deck end"
    },
    {
      "label": "horizontal dimension",
      "value": "1500",
      "unit": "",
      "appliesTo": "left deck underside"
    },
    {
      "label": "horizontal dimension",
      "value": "2850",
      "unit": "",
      "appliesTo": "left deck underside"
    },
    {
      "label": "horizontal dimension",
      "value": "1500",
      "unit": "",
      "appliesTo": "abutment/pile cap"
    },
    {
      "label": "end spacing",
      "value": "750",
      "unit": "",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "pile spacing",
      "value": "3600",
      "unit": "",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "end spacing",
      "value": "750",
      "unit": "",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "overall pile cap length",
      "value": "12300",
      "unit": "",
      "appliesTo": "pile cap"
    },
    {
      "label": "filter media thickness",
      "value": "600",
      "unit": "THK.",
      "appliesTo": "filter media"
    },
    {
      "label": "bored cast-in-situ pile diameter",
      "value": "1200",
      "unit": "DIA",
      "appliesTo": "bored cast-in-situ piles"
    },
    {
      "label": "scale",
      "value": "1:150",
      "unit": "",
      "appliesTo": "SECTION A-A"
    }
  ],
  "notes": [
    "POT-PTFE BEARING (TYP.)",
    "RCC SEISMIC STOPPER",
    "STONE PITCHING",
    "INDEPENDENT RETAINING WALL",
    "600 THK. FILTER MEDIA",
    "1200 DIA BORED CAST-IN-SITU PILES"
  ],
  "labels": [
    "A2",
    "C OF EXP. JOINT",
    "C OF BRG.",
    "SECTION A-A",
    "(SCALE 1:150)"
  ],
  "description": "This crop shows SECTION A-A through a bridge end support, including the deck expansion-joint area, abutment seat, bearing, seismic stopper, and piled foundation. A sloping wingwall/retaining element, stone pitching, filter media, and a partial independent retaining wall are also shown."
}

p02_r05 section a aSection

  • filter media×1tapered layerShown adjacent to the independent retaining wall.

1070 dimension (SQ.)1236 dimension (SK.)80 EXP.GAP (SQ.)92 EXP.GAP (SK)3500 dimension (SQ)230 vertical dimension2650 vertical dimension1500 horizontal dimension+11 more