Drawing to BOQpipeline control sheet
← Mindmapwhat the drawings said

pick-ups

1 page · 2 crops

⚠ No class in the bridge ontology fits this itemAdd a class

The item is insufficiently identified and the ontology would need a pickup insert class.

Every dimension read for it3

  • 1'-6 3/16"Partial dimension at top of cropnot attributedp10 · p10_r05 general construction notes 1 12 for beam
  • 4"Pickup embedment distance from bottom of beamp10 · p10_r05 general construction notes 1 12 for beam
  • 4"Pick-up embedment from bottom of beamp10 · p10_r06

Notes on the sheets that carry it

  • p101. BEAMS SHALL BE MAINTAINED IN AN UPRIGHT POSITION AT ALL TIMES AND SHALL BE PICKED UP WITHIN 4'-6" FROM THEIR ENDS. DISREGARDING THIS REQUIREMENT COULD LEAD TO COLLAPSE OF THE BEAM. PICK-UPS SHALL BE EMBEDDED TO WITHIN 4" OF THE BOTTOM OF THE BEAM. DETAILS OF PICK-UPS SHALL BE INCLUDED IN THE SHOP DRAWINGS.
  • p102. CHAMFER EDGES OF BEAMS 1/2" OR 3/4".
  • p103. HORIZONTAL DIMENSIONS ARE IN PLACE DIMENSIONS. THE BEAM LENGTH INCLUDES THE 1/8" EPOXY MORTAR AT EACH END. SHOP DRAWINGS SHALL ADJUST HORIZONTAL DIMENSIONS FOR GRADE AND FABRICATION EFFECTS SUCH AS SHRINKAGE AND ELASTIC SHORTENING.
  • p104. AT ℄ BEARING, FORM A 1 3/4" DIAMETER X 7" DEEP HOLE AT THE FIXED ENDS AND A 4" X 1 3/4" X 7" DEEP SLOT AT THE EXPANSION ENDS FOR A 1 1/2" DIAMETER SMOOTH DOWEL. SEE PLAN AND ELEVATION SHEET FOR LOCATION OF FIXED AND EXPANSION ENDS.
  • p105. TOPS OF BEAMS SHALL BE ROUGH FLOATED AT APPROXIMATELY THE TIME OF INITIAL SET. ENTIRE TOP SHALL BE SCRUBBED TRANSVERSELY WITH A COARSE BRUSH TO REMOVE ALL LAITANCE AND TO PRODUCE A ROUGHENED SURFACE FOR BONDING TO THE SLAB. ROUGHENED SURFACE SHALL HAVE AN AMPLITUDE OF APPROXIMATELY 1/4". CONCRETE FINS OR PROJECTIONS SHALL BE REMOVED TO PRODUCE A VERTICAL FACE AT THE EDGE OF THE BEAM.
  • p106. ALL HOLES FORMED INTO THE BEAMS TO FACILITATE TRANSPORT SHALL BE FILLED AND GIVEN A TYPE I FINISH, PRIOR TO ACCEPTANCE OF THE BEAM. REMOVE PVC OR SIMILAR FORMING MATERIALS FROM EACH HOLE, EXPOSING THE CONCRETE SURFACE. COAT INTERIOR OF HOLE WITH A TYPE II EPOXY RESIN ADHESIVE IN ACCORDANCE WITH GEORGIA STANDARD SPECIFICATION 886 AND FILL WITH A RAPID SETTING PATCHING MATERIAL IN ACCORDANCE WITH GEORGIA STANDARD SPECIFICATION 934.
  • p107. NON-COMPOSITE DEAD LOAD DEFLECTION (ΔNC) AT THE MIDPOINT IS DUE TO THE WEIGHT OF THE SLAB AND COPING.
  • p108. COMPOSITE DEAD LOAD DEFLECTION (ΔC) AT THE MIDPOINT IS DUE TO THE WEIGHT OF BARRIER.
  • p109. STRANDS SHALL MEET ALL REQUIREMENTS OF ASTM A 416 GRADE 270.
  • p1010. PRESTRESSING DATA IS AS FOLLOWS:
  • p10A. USE 20 - 1/2" DIAMETER SPECIAL LOW-RELAXATION (A = 0.167 SQ IN) STRANDS. PRETENSION STRANDS TO 33,818 LBS EACH.
  • p10B. PRETENSIONED STRANDS SHALL BE RELEASED AFTER THE CONCRETE HAS REACHED A MINIMUM STRENGTH (fci) OF 5,200 PSI.
  • p10C. INCLUDING THE TOP STRANDS, THE TOTAL JACKING FORCE OF PRETENSIONING IS 676,350 LBS.
  • p10D. INCLUDING THE TOP STRANDS, THE NET PRESTRESSING FORCE OF THE STRANDS AFTER ALL LOSSES IS 536,584 LBS.
  • p1011. CONCRETE STRENGTH (f'c) = 6,500 PSI.
  • p1012. ALLOWABLE PSC BEAM TENSION = 484 PSI.

Every crop it was read in — the drawing beside what the model took off it

Page 10

crop

p10_r05 general construction notes 1 12 for beam

page 10 · gdot_plan_ab5a9057847f41e3bb9d0ead3c6f2c22_p10_r05_general_construction_notes_1_12_for_beam
Original
p10_r05 general construction notes 1 12 for beam
{
  "view": "Notes",
  "objects": [
    {
      "name": "PSC beam",
      "tag": "",
      "shape": "",
      "material": "precast prestressed concrete",
      "count": null,
      "note": "Beam requirements, handling, finish, prestressing, concrete strength, and allowable tension are noted."
    },
    {
      "name": "pick-ups",
      "tag": "",
      "shape": "",
      "material": "",
      "count": null,
      "note": "Embedded pick-ups are specified for beam handling."
    },
    {
      "name": "smooth dowel",
      "tag": "",
      "shape": "circular",
      "material": "",
      "count": null,
      "note": "Specified at fixed and expansion bearing ends."
    },
    {
      "name": "slab",
      "tag": "",
      "shape": "",
      "material": "",
      "count": null,
      "note": "Referenced for bonding and dead-load deflection."
    },
    {
      "name": "coping",
      "tag": "",
      "shape": "",
      "material": "",
      "count": null,
      "note": "Referenced for non-composite dead-load deflection."
    },
    {
      "name": "barrier",
      "tag": "",
      "shape": "",
      "material": "",
      "count": null,
      "note": "Referenced for composite dead-load deflection."
    },
    {
      "name": "prestressing strands",
      "tag": "",
      "shape": "circular",
      "material": "special low-relaxation steel",
      "count": 20,
      "note": "Pretensioned strands are specified."
    }
  ],
  "measurements": [
    {
      "label": "Partial dimension at top of crop",
      "value": "1'-6 3/16\"",
      "unit": "",
      "appliesTo": ""
    },
    {
      "label": "Beam pickup distance from ends",
      "value": "4'-6\"",
      "unit": "",
      "appliesTo": "PSC beam"
    },
    {
      "label": "Pickup embedment distance from bottom of beam",
      "value": "4\"",
      "unit": "",
      "appliesTo": "pick-ups"
    },
    {
      "label": "Beam edge chamfer",
      "value": "1/2\" OR 3/4\"",
      "unit": "",
      "appliesTo": "PSC beam"
    },
    {
      "label": "Epoxy mortar at each beam end",
      "value": "1/8\"",
      "unit": "",
      "appliesTo": "PSC beam"
    },
    {
      "label": "Fixed-end hole diameter",
      "value": "1 3/4\"",
      "unit": "",
      "appliesTo": "smooth dowel"
    },
    {
      "label": "Fixed-end hole depth",
      "value": "7\"",
      "unit": "",
      "appliesTo": "smooth dowel"
    },
    {
      "label": "Expansion-end slot size",
      "value": "4\" X 1 3/4\" X 7\"",
      "unit": "",
      "appliesTo": "smooth dowel"
    },
    {
      "label": "Smooth dowel diameter",
      "value": "1 1/2\"",
      "unit": "",
      "appliesTo": "smooth dowel"
    },
    {
      "label": "Roughened surface amplitude",
      "value": "1/4\"",
      "unit": "",
      "appliesTo": "PSC beam"
    },
    {
      "label": "Strand quantity",
      "value": "20",
      "unit": "",
      "appliesTo": "prestressing strands"
    },
    {
      "label": "Strand diameter",
      "value": "1/2\"",
      "unit": "",
      "appliesTo": "prestressing strands"
    },
    {
      "label": "Strand area",
      "value": "0.167",
      "unit": "SQ IN",
      "appliesTo": "prestressing strands"
    },
    {
      "label": "Pretension force per strand",
      "value": "33,818",
      "unit": "LBS",
      "appliesTo": "prestressing strands"
    },
    {
      "label": "Minimum concrete strength for strand release",
      "value": "5,200",
      "unit": "PSI",
      "appliesTo": "PSC beam"
    },
    {
      "label": "Total jacking force of pretensioning",
      "value": "676,350",
      "unit": "LBS",
      "appliesTo": "prestressing strands"
    },
    {
      "label": "Net prestressing force after all losses",
      "value": "536,584",
      "unit": "LBS",
      "appliesTo": "prestressing strands"
    },
    {
      "label": "Concrete strength (f'c)",
      "value": "6,500",
      "unit": "PSI",
      "appliesTo": "PSC beam"
    },
    {
      "label": "Allowable PSC beam tension",
      "value": "484",
      "unit": "PSI",
      "appliesTo": "PSC beam"
    }
  ],
  "notes": [
    "1. BEAMS SHALL BE MAINTAINED IN AN UPRIGHT POSITION AT ALL TIMES AND SHALL BE PICKED UP WITHIN 4'-6\" FROM THEIR ENDS. DISREGARDING THIS REQUIREMENT COULD LEAD TO COLLAPSE OF THE BEAM. PICK-UPS SHALL BE EMBEDDED TO WITHIN 4\" OF THE BOTTOM OF THE BEAM. DETAILS OF PICK-UPS SHALL BE INCLUDED IN THE SHOP DRAWINGS.",
    "2. CHAMFER EDGES OF BEAMS 1/2\" OR 3/4\".",
    "3. HORIZONTAL DIMENSIONS ARE IN PLACE DIMENSIONS. THE BEAM LENGTH INCLUDES THE 1/8\" EPOXY MORTAR AT EACH END. SHOP DRAWINGS SHALL ADJUST HORIZONTAL DIMENSIONS FOR GRADE AND FABRICATION EFFECTS SUCH AS SHRINKAGE AND ELASTIC SHORTENING.",
    "4. AT ℄ BEARING, FORM A 1 3/4\" DIAMETER X 7\" DEEP HOLE AT THE FIXED ENDS AND A 4\" X 1 3/4\" X 7\" DEEP SLOT AT THE EXPANSION ENDS FOR A 1 1/2\" DIAMETER SMOOTH DOWEL. SEE PLAN AND ELEVATION SHEET FOR LOCATION OF FIXED AND EXPANSION ENDS.",
    "5. TOPS OF BEAMS SHALL BE ROUGH FLOATED AT APPROXIMATELY THE TIME OF INITIAL SET. ENTIRE TOP SHALL BE SCRUBBED TRANSVERSELY WITH A COARSE BRUSH TO REMOVE ALL LAITANCE AND TO PRODUCE A ROUGHENED SURFACE FOR BONDING TO THE SLAB. ROUGHENED SURFACE SHALL HAVE AN AMPLITUDE OF APPROXIMATELY 1/4\". CONCRETE FINS OR PROJECTIONS SHALL BE REMOVED TO PRODUCE A VERTICAL FACE AT THE EDGE OF THE BEAM.",
    "6. ALL HOLES FORMED INTO THE BEAMS TO FACILITATE TRANSPORT SHALL BE FILLED AND GIVEN A TYPE I FINISH, PRIOR TO ACCEPTANCE OF THE BEAM. REMOVE PVC OR SIMILAR FORMING MATERIALS FROM EACH HOLE, EXPOSING THE CONCRETE SURFACE. COAT INTERIOR OF HOLE WITH A TYPE II EPOXY RESIN ADHESIVE IN ACCORDANCE WITH GEORGIA STANDARD SPECIFICATION 886 AND FILL WITH A RAPID SETTING PATCHING MATERIAL IN ACCORDANCE WITH GEORGIA STANDARD SPECIFICATION 934.",
    "7. NON-COMPOSITE DEAD LOAD DEFLECTION (ΔNC) AT THE MIDPOINT IS DUE TO THE WEIGHT OF THE SLAB AND COPING.",
    "8. COMPOSITE DEAD LOAD DEFLECTION (ΔC) AT THE MIDPOINT IS DUE TO THE WEIGHT OF BARRIER.",
    "9. STRANDS SHALL MEET ALL REQUIREMENTS OF ASTM A 416 GRADE 270.",
    "10. PRESTRESSING DATA IS AS FOLLOWS:",
    "A. USE 20 - 1/2\" DIAMETER SPECIAL LOW-RELAXATION (A = 0.167 SQ IN) STRANDS. PRETENSION STRANDS TO 33,818 LBS EACH.",
    "B. PRETENSIONED STRANDS SHALL BE RELEASED AFTER THE CONCRETE HAS REACHED A MINIMUM STRENGTH (fci) OF 5,200 PSI.",
    "C. INCLUDING THE TOP STRANDS, THE TOTAL JACKING FORCE OF PRETENSIONING IS 676,350 LBS.",
    "D. INCLUDING THE TOP STRANDS, THE NET PRESTRESSING FORCE OF THE STRANDS AFTER ALL LOSSES IS 536,584 LBS.",
    "11. CONCRETE STRENGTH (f'c) = 6,500 PSI.",
    "12. ALLOWABLE PSC BEAM TENSION = 484 PSI."
  ],
  "labels": [
    "NOTES",
    "℄ BEARING TO",
    "EL"
  ],
  "description": "This crop is a notes block for PSC beams, with general beam handling, fabrication, bearing-dowel, surface preparation, transport-hole repair, and deflection notes. It also provides prestressing strand data, concrete strength, and allowable PSC beam tension; only a partial dimension and partial adjacent drawing labels are visible at the top."
}

p10_r05 general construction notes 1 12 for beamNotes

  • pick-upsEmbedded pick-ups are specified for beam handling.

1'-6 3/16" Partial dimension at top of crop4'-6" Beam pickup distance from ends4" Pickup embedment distance from bottom of beam1/2" OR 3/4" Beam edge chamfer1/8" Epoxy mortar at each beam end1 3/4" Fixed-end hole diameter7" Fixed-end hole depth4" X 1 3/4" X 7" Expansion-end slot size+11 more

crop

p10_r06

page 10 · psc_beam_p10_r06
Original
p10_r06
{
  "view": "Notes",
  "objects": [
    {
      "name": "Beams",
      "tag": "",
      "shape": "",
      "material": "",
      "count": null,
      "note": "Beam handling, pick-up, and chamfer requirements are noted."
    },
    {
      "name": "Pick-ups",
      "tag": "",
      "shape": "",
      "material": "",
      "count": null,
      "note": "To be embedded near the bottom of the beam; details to be included in shop drawings."
    }
  ],
  "measurements": [
    {
      "label": "Pick-up location from beam ends",
      "value": "4'-6\"",
      "unit": "",
      "appliesTo": "Beams"
    },
    {
      "label": "Pick-up embedment from bottom of beam",
      "value": "4\"",
      "unit": "",
      "appliesTo": "Pick-ups"
    },
    {
      "label": "Beam edge chamfer",
      "value": "1/2\"",
      "unit": "",
      "appliesTo": "Beams"
    },
    {
      "label": "Beam edge chamfer",
      "value": "3/4\"",
      "unit": "",
      "appliesTo": "Beams"
    }
  ],
  "notes": [
    "1. BEAMS SHALL BE MAINTAINED IN AN UPRIGHT POSITION AT ALL TIMES AND SHALL BE PICKED UP WITHIN 4'-6\" FROM THEIR ENDS. DISREGARDING THIS REQUIREMENT COULD LEAD TO COLLAPSE OF THE BEAM. PICK-UPS SHALL BE EMBEDDED TO WITHIN 4\" OF THE BOTTOM OF THE BEAM. DETAILS OF PICK-UPS SHALL BE INCLUDED IN THE SHOP DRAWINGS.",
    "2. CHAMFER EDGES OF BEAMS 1/2\" OR 3/4\"."
  ],
  "labels": [],
  "description": "This crop is a notes block containing beam handling and lifting requirements. It also specifies chamfering of beam edges."
}

p10_r06Notes

  • Pick-upsTo be embedded near the bottom of the beam; details to be included in shop drawings.

4'-6" Pick-up location from beam ends4" Pick-up embedment from bottom of beam1/2" Beam edge chamfer3/4" Beam edge chamfer